![ptx-59235_ve_ml](http://www.hongteckhin.com.sg/cdn/shop/products/ptx-59235_ve_ml.jpg?v=1687491011&width=250)
Permatex High-Temperature Thread Sealant
Description
Permatex High Temperature Thread Sealant is a medium
strength anaerobic sealant with PTFE for tapered pipe threads.
This sealing compound is of a white, creamy paste
consistency. The high lubricating properties of this compound
prevents galling on pipe threads and fittings. It will provide
immediate low pressure sealing and allow for the readjustment
of fittings shortly after assembly. After 72 hours the joint is
sealed to pipe burst pressure. This product has a medium
solvent resistance and will withstand temperatures to 400F
(204C). This product is not recommended for use on
plastic piping.
The rate of cure will depend on the ambient temperature. Full
cure is attainable in 24 hours at room temperature, 72F
(22C), or 1 hour at 200F (93C).
The rate of cure will depend on the material used. Permatex
High Temperature Thread Sealant will react faster and
stronger with Active Metals. However, Inactive Metals will
require the use of an activator (Surface Prep) to obtain
maximum strength and cure speed at room temperature.
Where cure speed is unacceptably long, or large gaps are
present, applying an activator (Surface Prep) to the surface
will improve cure speed. Assemblies will fully cure in 24 hours
with activator.
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 46F and 82F
(8C and 28C) unless otherwise labeled. Optimal storage is
at the lower half of this temperature range. To prevent
contamination of unused product, do not return any material to
its original container.
SDS
TDS
Read More
Read Less
Permatex High-Temperature Thread Sealant
Permatex High Temperature Thread Sealant is a medium
strength anaerobic sealant with PTFE for tapered pipe threads.
This sealing compound is of a white, creamy paste
consistency. The high lubricating properties of this compound
prevents galling on pipe threads and fittings. It will provide
immediate low pressure sealing and allow for the readjustment
of fittings shortly after assembly. After 72 hours the joint is
sealed to pipe burst pressure. This product has a medium
solvent resistance and will withstand temperatures to 400F
(204C). This product is not recommended for use on
plastic piping.
PRODUCT BENEFITS
- Resists leakage, vibration loosening, moisture, hydraulic
fluids, diesel fuels. - Lubricates threads for easy assembly and disassembly.
- Will not shred or wear like tapes.
- Parts may be repositioned for up to 24 hours after
application.
TYPICAL APPLICATIONS
- Head bolts into through holes
- Oil PSI sending units/sensors
- Oil and coolant lines
- Fuel fittings
- Rear axle fill plug
- Brake and power steering fittings
DIRECTIONS FOR USE
- For best performance, surfaces should be clean and free
of grease. - Product should be applied to the thread engagement
area in sufficient quantity to fill all engaged threads. - Use accepted trade practices to assemble and wrenchtighten fittings until proper alignment is obtained.
- Very large thread sizes may create large gaps, which will
affect cure speed and strength. - For maximum pressure and solvent resistance, allow at
least 24 hours for the product to fully cure before filling
and pressurizing system. - Fittings assembled with Permatex High Temperature
Thread Sealant may be disassembled with normal hand
tools. - For large pipe diameters (over 1"), heat may be required
to disassemble fittings. - Fittings may be reused by removing loose sealant
residue with a wire brush and reapplying sealant.
FOR CLEANUP
- Wipe off any material outside the joint with a dry cloth.
- Clean hands with Permatex Fast Orange® hand cleaner
or soap and water. - Cured material must be removed with Permatex Gasket
Remover.
TYPICAL CURING PERFORMANCE
Cure speed vs. temperature
The rate of cure will depend on the ambient temperature. Full
cure is attainable in 24 hours at room temperature, 72F
(22C), or 1 hour at 200F (93C).
Cure speed vs. substrate
The rate of cure will depend on the material used. Permatex
High Temperature Thread Sealant will react faster and
stronger with Active Metals. However, Inactive Metals will
require the use of an activator (Surface Prep) to obtain
maximum strength and cure speed at room temperature.
Cure speed vs. activator
Where cure speed is unacceptably long, or large gaps are
present, applying an activator (Surface Prep) to the surface
will improve cure speed. Assemblies will fully cure in 24 hours
with activator.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
STORAGE
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 46F and 82F
(8C and 28C) unless otherwise labeled. Optimal storage is
at the lower half of this temperature range. To prevent
contamination of unused product, do not return any material to
its original container.
SDS
TDS
![ptx-59235_ve_ml](http://www.hongteckhin.com.sg/cdn/shop/products/ptx-59235_ve_ml.jpg?v=1687491011&width=250)
Permatex High-Temperature Thread Sealant
Sale price$0.00
Regular price (/)
Products và Adhesive / Sealant
Categories
Permatex
Products Brand