Threebond 1521 Synthetic Rubber Adhesive

0.0

Description

Threebond 1521 Synthetic Rubber Adhesive


ThreeBond® Synthetic Rubber Adhesive 1521 is a multi-purpose, rubber based adhesive.
Bonds rubber, plastic, vinyl, metal, leather, and grips

It is suitable for bonding a wide range of substrates including metals, rubbers and plastics, giving a high initial bond strength after setting. TB1521 is widely used as a contact adhesive in various applications such as bonding automotive sound insulating materials, carpets, plastic and interior trim, decorative laminates and so on.
Features

Materials which can be bonded:
  • Metals (Iron, Aluminium, Duraluminium, Brass, etc.)
  • Plastics (Polyvinylchloride, Polymethacrylic, Phenolic resin,
    Polystyrene, Ebonite, etc.)
  • Non-metals (Wood, fabrics, leather, ceramics, paper,
    concrete, mortar, etc.)
  • Natural and synthetic rubbers (CR,SBR, EPDM, NBR, etc.)
    (Note: The product is not suitable for bonding Polyethylene,
    Polypropylene and Fluororesin.)
Directions for Use
  • Surfaces must be clean, dry and free from oil or greasy
    deposits.
  • Stir well before use. After long term storage a precipitated
    layer may form but this does not mean the cement is no
    longer usable.
  • Apply a thin even coat to one or both surfaces by brush,
    knife, or other spreading method. Coating both surfaces is
    preferred since it improves bond strength and permits longer
    open time.
  • Coverage is approximately 3m²/kg for a dry film thickness of
    0.1mm.
  • Absorbant surfaces may require more than one coat. Bond
    whilst adhesive is still wet or aggresively tacky.
  • For non-porous surfaces allow the adhesive to dry until it is
    tacky. Join the surfaces with firm pressure.
  • Open time for one surface application is 5 minutes or 30
    minutes for two surfaces application. This drying time
    depends on temperature, humidity, and the porosity of the
    materials to be bonded.
  • Reactivation bonding method:
    Re-moistening method: Allow the surfaces to dry
    completely. After the solvent has completely evaporated
    apply a small amount of adhesive to give renewed tackiness
    and bond in the normal manner. This method gives greater
    immediate strength.
    Heat reactivation method: Allow the surfaces to dry
    completely. Join the surfaces and heat in an oven, press or
    under lamps at 120°C, maintaining adequate pressure to
    ensure intimate contact of the surfaces, whilst allowing
    sufficient time for the transfer of heat through mating parts to
    the adhesive film. Surfaces may be pre-coated in this way
    several days before final reactivation.
  • TB 1521 is highly flammable.
    Use only in well ventilated areas.
    Store in a cool, dark place in its original container tightly
    sealed to maintain shelf life.
Packaging

150 ml tube and 1kg, 15kg and 160 kg containers (special
packing on request).
Description of first aid measures
  • After inhalation : Supply fresh air. If required, provide artificial respiration. Keep
    patient warm. Consult doctor if symptoms persist.
    In case of unconsciousness place patient stably in side position
    for transportation.
  • After skin contact : Immediately wash with water and soap and rinse thoroughly.
    If skin irritation continues, consult a doctor.
  • After eye contact : Rinse opened eye for several minutes under running water. Then
    consult a doctor.
  • After swallowing : Do not induce vomiting; call for medical help immediately.
    A person vomiting while lying on their back should be turned onto
    their side.
    Induce vomiting, only if affected person is fully conscious.
 
 
Read More Read Less
Products và Adhesive / Sealant

Categories

Threebond

Products Brand

You may also like