Loctite E30cl Epoxy Adhesive Cartridge Clear 50ml

Loctite E30cl Epoxy Adhesive Cartridge Clear 50ml

• Shear Strength, Steel : 3100 psi
• Temperature Resistance : 250 °F
• Viscosity : 10000 mPa.s (cP) Brookfield
• Key Substrates : Ceramic, Glass, Metal, Plastic
• Color : Clear: Ultra Clear
• Curing Type : Heat cure
• Application : Potting and Bonding

LOCTITE®EA E-30CL is a clear, colorless to slightly yellowish, 2-part, low viscosity, industrial grade epoxy adhesive. It cures at room temperature with minor shrinkage to form an ultra clear adhesive bondline with excellent impact resistance. It resists a wide range of chemicals and solvents and bonds most materials including glass, optical fibers, ceramics, metals and many rigid plastics.

• Cures at room temperature with minimal shrinkage to form an ultra clear adhesive bondline
• Excellent impact resistance
• Has excellent dimensional stability over a wide temperature range
• Used in bonding, small potting, staking and laminating applications where optical clarity and excellent structural, mechanical and electrical insulating properties are required

LOCTITE® EA E-30CL™ is a low viscosity, industrial grade
epoxy adhesive. Once mixed, the two component epoxy cures
at room temperature with minimal shrinkage to form an ultra
clear adhesive bondline with excellent impact resistance. The
fully cured epoxy is resistant to a wide range of chemicals and
solvents and has excellent dimensional stability over a wide
temperature range. Typical applications include bonding, small
potting, staking and laminating applications where optical
clarity and excellent structural, mechanical and electrical
insulating properties are required. LOCTITE® EA E-30CL™
bonds most materials including glass, optical fibers, ceramics,
metals, and many rigid plastics.

TYPICAL CURING PERFORMANCE

Cure Speed vs. Time

The graph below shows shear strength developed with time on
abraded, acid etched aluminum lapshears @ 25 °C with an
average bondline gap of 0.1 to 0.2 mm and tested according to
ISO 4587.

GENERAL INFORMATION

This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).

Directions For Use:

1. Use gloves to minimize skin contact. DO NOT use
   solvents for cleaning hands.
2. Dual Cartridges: To use simply insert the cartridge into
   the application gun and start the plunger into the cylinders
   using light pressure on the trigger. Next, remove the
   cartridge cap and expel a small amount of adhesive to be
   sure both sides are flowing evenly and freely. If automatic
   mixing of resin and hardener is desired, attach the mixing
   nozzle to the end of the cartridge and begin dispensing
   the adhesive. Bulk Containers: Utilize volumetric
   dispensing system to ensure proper mix ratio and utilize
   mix nozzle to obtain adequate mixing.
3. Allow 24 hours at 22 °C for cure. Heat up to 93°C will
   speed curing. Maximum chemical resistance is achieved
   after seven days at 22°C.
4. Mixed product is free flowing and self leveling. Potting
   voids by moving the discharge point from the bottom up
   will give the best results.
5. Keep parts from moving during cure. Parts must be
   positioned to contain the product inside the potting voids
   during the cure.
6. Excessive uncured adhesive can be cleaned up with
   ketone type solvents.

Loctite Material Specification

LMS dated July-03, 2001 (Resin) and LMS dated July-23,
2001 (Hardener). Test reports for each batch are available for
the indicated properties. LMS test reports include selected QC
test parameters considered appropriate to specifications for
customer use. Additionally, comprehensive controls are in
place to assure product quality and consistency. Special
customer specification requirements may be coordinated
through Henkel Loctite Quality.

Storage

Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.